Ibis Ripley SLX Build
Updated for 2022 the 29″ carbon adventure / trail / light enduro Ripley frame is available 6 builds. Starting at $5,899 the Ibis Ripley SLX Build offers riders the top tier carbon frame and DW Suspension design.
All of the Ripley builds are highlighted with FOX Factory Suspension.
The stock fork offering is the FOX 34 GRIP2 and the rear shock is spec’d with the FOX Float Factory DPS.
Learn more about the available suspension adjustments below or skip to the SLX Build Kit Spec.
FOX Float 34 Factory Series GRIP2
Ibis Ripley Fork Travel Options
130mm Ibis Ripley
The Ripley is spec’d with a 130mm FOX 34. This provides the bike with it’s stock 66.5 degree headtube angle and 335mm bottom bracket height.
Riders looking for a little more aggressive setup may investigate the 140mm option.
140mm Ibis Ripley
Perhaps more than the additional 9% of travel the 10mm adds are the geometry modifications. Raising the front of the Ripley will slacken the headtube, increase the trail measurement and slightly lift the bottom bracket.
These are popular shifts for riders pushing the Ripley into bigger trails, attacking the steepest, burliest terrain.
Wondering which is right for you? Chat with our team today and we’ll help you define which riders benefit from which travel setup.
Air Spring & Volume Spacers
The FOX 34 provides riders a range of setup options using air spring as well as volume spacers.
Suggested sag is 15% for a firm feel and 20% for a plush fork. On the stock 130mm setup 15% equals 20mm or about 0.8 inch of sag. 20% will use 26mm or about 1″ of sag.
Riders who choose the 140mm option will find the sag settings quite close to the 160. 15% is 21mm while 20% is 28mm. (as mentioned in the previous tab the additional travel is more about the geometry change than “more” travel).
The 130mm FOX 34 is factory spec’d with 2 volume spacers (bike manufacturers may or may not change this). The 130mm fork can carry a maximum of 5 volume spacers.
At 140mm the factory spec is 1 volume spacers with a maximum of 5.
Do not install more volume spacers than the FOX advises. Installing more than the maximum volume spacers will result in product damage and potential for injuries, etc.
FOX 34 GRIP2 Rebound Controls
The GRIP2 damper provides both Low (LSR) and High (HSR) rebound controls.
The addition of the High Speed or HSR control provides increased rebound control to account for the higher PSI produced by aggressive or heavier riders.
Typically riders will adjust LSR, Low Speed Rebound, to suit riding style and taste and refer to FOX’s guide for the appropriate HSR, High Speed Rebound, pairing.
FOX GRIP2 Compression Controls
The FOX GRIP2 damper provides Low and High speed compression controls to fine tune support.
Compression circuits hydraulically damp (or slow) the fork’s input assisting the air spring in providing appropriate mid-stroke and bottom out feel.
Low Speed Compression helps provide mid-stroke support. This allows a bike to ride taller in the travel in cornering while resisting brake dive, rider weight shift and other slow shaft speed inputs.
High Speed Compression works to fine tune bottom out feel as well as other high shaft speed inputs also known as square edge bumps. Example: if you sprint straight into a curb you’re likely to engage the High Speed Compression even if you’re not using full travel. This is due to the speed of the shaft moving oil to compensate for the hit.
FOX Float Factory DPS
Air Spring & Volume Spacers
The Ibis Ripley uses a 190 x 45mm shock, spec’d with the Fox Float Factory DPS.
SAG is adjusted by PSI – typically trail riding styles gravitate to 25-30% sag. This would measure about 13mm for a plush setup and 11mm for a more firm setup.
Volume spacing provides fine tuning options to support the air spring.
By changing to a larger volume spacer, thus reducing the volume, you increase the air spring’s ramp rate for improved bottom out support and pop.
Conversely smaller volume spacers produces a more linear feel as the air has more volume during shock compression per mm of travel.
Do not install more or larger volume spacers than the FOX advises. Installing more than the maximum volume spacers will result in product damage and potential for injuries, etc.
FOX FLOAT FACTORY DPS Rebound Controls
The DPS provides a rebound control with 11 clicks of adjustment.
Heavier riders will use more rebound control than lighter riders to slow the air spring’s return to neutral.
As your ground speeds increase it is common to allow your bike to rebound more quickly to prepare for the next terrain feature and avoid suspension packing from slow rebound setup.
FOX Float Factory DPS Compression Controls
The Fox Float Factory DPS shock provides two controls to help fine tune compression.
First is the blue 3 position switch which adjusts from Firm, Mid and Open. Also known as a “climb switch” the use of this is dependent on rider style, preference and terrain.
Fine tuning the low speed compression can be accomplished in the Open mode by adjusting the black dial located around the circumference of the blue 3 position switch.
3 settings are available with “1” being the most plus and “3” the most firm.
Ibis Ripley SLX Build Component Spec
note: supply chain issues may result in frequent substitutions for similar parts at Ibis’ discretion.
Ripley SLX Kit
Fox Float 34 Factory Series 130mm, 29”, 110×15
Fox Float Factory Series, DPS with EVOL, 190 x 45
Ibis Logo Front Hub, 110×15, 32 Hole
Ibis Logo Rear Hub, 148×12, 32 Hole
Ibis S35 Alloy, 32 hole, 29″
Sapim Dlight Double Butted
Sapim 14G Alloy
Maxxis DHR2 29″ x 2.4″ Exo TR
Maxxis Dissector 29″ x 2.4″ Exo TR
Shimano SLX M7120 4p
Shimano SM-RT66 180
Shimano SLX M7100 24mm spindle, 30t Alloy Ring
Shimano SLX BB52
Shimano SLX M7100 Shadow Plus
Shimano SLX M7100
Shimano SLX 10-51
Shimano SLX M7100
Cane Creek 40: ZS44/ZS56
Lizard Skin Charger
Ibis 780mm Alloy
Bike Yoke Revive Dropper
WTB Silverado 142
Popular Upgrades to the Ibis Ripley Complete
There are a variety of popular upgrades or part swaps on the Ibis complete bikes. Flip through the tabs below to explore some of the most popular including Brakes, Tires, Chain Guides and Frame Protection.
Along with tires the most common upgrade or swap to a stock Ibis build is brakes.
Brakes are extremely important to your bike’s personality as well as your confidence on trail.
Finding brakes with the right modulation and power for your riding style allows you to further fine tune performance with rotor size.
Brake modulation is how the lever position relates to the amount of power at the caliper.
Brands like Magura and Hope offer great modulation. A slight pull on the lever will produce less pressure at the caliper and increases as lever throw continues. Magura riders can fine tune this even further with a variety of short or long brake levers to further modify the leverage ratio. In fact, Magura offers brake levers with adjustable modulation!
Shimano brakes have less modulation and the power tends to “come on” quicker. This isn’t necessarily good or bad – it’s just a personality.
Magura and Shimano offer similar levels of total power differing in personality more on modulation than max power or feel.
Hope brakes have a little less “bite” at full power but most riders are able to fine tune this by running a slightly larger rotor to increase both leverage and heat capacity.
Pricing / Value
Interested in updating the brakes but on a tight budget? Check out the Magura MT5. In many cases it’s available as a No-Cost upgrade. Cost conscious yes, light on performance or service life? Not a chance. The MT5 brake is the most popular offering here at BikeCo.com
Ripley Tire Upgrades / Swaps
The Ibis Ripley kits are spec’d with Maxxis Dissector EXO 29×2.4″ front tire and Maxxis DHR II 29×2.4″ rear tires. These are on the very aggressive end of the spectrum for tread pattern and about average for sidewall support and protection on current trail tire options.
Since tires play such a big role in a bike’s personality it’s very common for clients to swap to other tread patterns, sidewalls or sizes.
Some of the most popular changes are listed below.
Front Tire: Spec’d Maxxis Dissector
This is a very aggressive, tall lugged, open spaced tread pattern. Frankly not many conditions parallel this tire with the Ibis Ripley’s personality.
Riders looking for a bit faster rolling front tire typically review the Maxxis DHR II and DHF.
While the DHR II is branded as a rear tire it is popular as a front tire in some conditions. This is due to the slightly larger spacing and braking sipes in the tires center section.
The Maxxis DHF is probably the most popular front tire across MTB. Designed with tall cornering knobs and moderate center section the DHF is designed to roll fast and corner hard.
Ripley riders may decide to go faster than the DHF balancing the decreased weight and grip levels to their terrain. The Aggressor is shown, but tends to be a better rear tire as the large spacing on the cornering lugs can lead to slide during direction changes.
The “fast” end of the tire spectrum would be the Ardent and Rekon front tire options for the Ripley.
Rear Tire: Spec’d Maxxis DHR II
Ibis spec’s the Dissector front and DHR II rear tire giving the Ripley plenty of grip for the gnarliest terrain. However, most Ripley riders are looking for something that’s a bit faster rolling and poppy.
Riders looking for faster rolling rear tire options tend to shop the Maxxis DHR II, then the DHF (slightly tighter packed and faster than the DHR II), followed by the Aggressor.
The Aggressor paired with the DHF is probably the most popular pleasure riding tire combo for the Ibis Ripley. It provides enough bite in the burly terrain without having bike park level tires on your all day pedal adventures.
Looking to go even faster on the rear tire? Chat with us about the new Rekon tire’s with aggressive sidewall technologies for support.
The Ripley is spec’d with EXO sidewalls to provide riders additional support and puncture protection compared to the lighter, skinwall tires.
Below are the levels of additional sidewall protection and support available from Maxxis.
An extremely cut-resistant and abrasion-resistant material added to the sidewalls of select mountain tires. This densely woven fabric is also lightweight and highly flexible, ensuring that the performance of the tire remains unaffected. Choose EXO Protection for exceptionally rocky, treacherous trails where the chance of sidewall cuts and abrasions is high.
EXO+ construction combines two puncture protection materials: SilkShield and EXO. The SilkShield layer runs from bead-to-bead with a layer of EXO along the sidewalls. Combined, these two materials create EXO+ which improves tread puncture protection by 27%; sidewall durability by 51%; and resistance to pinch flats by 28%.
Riders looking for additional sidewall support and resistance to damage will shop the Double Down or DD options
DoubleDown (DD) is the next step in the evolution of the dual-ply tire casing for enduro racing. Two 120 TPI casing layers reinforced with a butyl insert provide the enduro racer with the support and protection of a downhill tire, but in a lighter package.
The “light” tire option for most enduro riders would be the EXO sidewall.
One of the most common upgrades to the Ibis Ripmo is adding a chain guide.
A variety of options are available depending on your riding needs.
The Wolf Tooth Gnarwolf is a great upper guide as is the OneUp option.
OneUp goes a step further with the Guide + Bash or, for riders who don’t need or want the upper guide, simply a lower bash to protect the chain ring and bottom bracket area.
The lower bash only is a popular option with oval chain ring setups that can be complex to pair with upper guides.
RideWrap Frame Protection
A popular upgrade for any mountain bike, we offer two options of RideWrap Frame protection.
The RideWrap Tailored Kit covers the majority of your frame based on individual model size and shape. This is a $95.00 addition. We will install the Tailored kit for an additional $250.00 labor at time of initial build.
RideWrap’s Covered Kit protects the high wear areas such as downtube, top tube, etc. Custom trimming of the stock Covered Kit helps with fitment depending on model and size. The Covered Kit is $65.00 and installation is $150.00 at time of build.
Installing RideWrap isn’t particularly hard – but it is time consuming. Thinking about doing the labor yourself? Awesome! Check out a quick video on the installation process below.
Compare Ibis Ripley Geometry
Using this form you can easily compare bottom bracket height, wheelbase, reach and stack between various sizes and models.
Data is displayed above selections, under the overlay graphic.
Other Ibis Ripley Builds
Deore – starting at $5,099
Entry level Shimano kit. 12sp 51t cassette and 4 piston Shimano brakes
NGX – starting at $5,399
Combination kit of SRAM NX and GX components. GX Cassette (XD hub driver – works with any SRAM cassette above NX)
XT – starting at $6,699
The most popular Shimano kit – 4 piston brakes and carbon fiber handlebar.
X01 – starting at $7,899
The most popular build kit featuring the new 52t Eagle Cassette.
XX1 AXS – starting at $11,499
Wireless shifting. Industry Nine hubs and Ibis Carbon rims.