Description
SRAM Trail, Guide, G2 Organic Brake Pads Aluminum backed
SRAM Disc Brake Pads – Organic Compound, Aluminum Backed, Quiet/Light, For SRAM Trail, SRAM Guide, and SRAM G2, pad shape 58
Original equipment pads for no-compromise disc brake performance.
Aluminum backed organic pad is quiet and lightweight
Each pad kit includes two pads, a pad spreader spring, pad pin and clip
Manufacturer Part Number: 00.5318.003.003
UPC: 710845756856
Pad Shape Number: 58
Backing Plate Material: Aluminum
Compound: Organic
SRAM Trail Organic Brake Pads – Aluminum Backer- Pad Shape 58
SRAM Guide Organic Brake Pads – Aluminum Backer- Pad Shape 58
SRAM G2 Organic Brake Pads – Aluminum Backer – Pad Shape 58
SRAM Brake Pads
Looking for other SRAM Brake Pads?
Pad Shape 01
Organic: for SRAM Level & Elixir 00.5315.035.031 with Steel Backing Plate
Organic: for SRAM Level, Elixir & DB 00.5318.024.001 with Steel Backing Plate
Organic with Aluminum Backer: for SRAM Level & Elixir 00.5315.035.020 with Aluminum Backing Plate
Sintered: for SRAM Level & Elixir 00.5315.035.010 with Steel Backing Plate
Springs and pad pins still in good shape? Save some money purchasing SRAM Level Pads Only here.
Pad Shape 36
Sintered: for SRAM Guide RE, Code (2011) 00.5315.023.010 with Steel Backing Plate
Organic with Aluminum Backer: for SRAM Guide RE, Code (2011) 00.5315.023.020 with Aluminum Backing Plate
Organic: for SRAM Guide RE, Code (2011) 00.5315.023.030 with Steel Backing Plate
SRAM Guide Brake Pads Only, no spring, pad pin or clip – Sintered and Organic available here.
SRAM Code Brake Pads Only available here
Pad Shape 58
Sintered: for SRAM Trail, Guide & G2 00.5318.003.005 with Steel Backing Plate
Organic with Aluminum Backer: for SRAM Trail, Guide & G2 00.5318.003.003 with Aluminum Backing Plate
Organic: for SRAM Trail, Guide & G2 00.5318.003.004 with Steel Backing Plate
Replacing your brake pads for the first time? Or just want to refresh the best practices? Check out a pair of videos about installing new brake pads and the importance of removing the bleed port prior to service.
Do You Need To Replace Your Rotors As Well?
The nature of brake pad and rotor interface means they will wear together. Ideally you will be able to replace your brake pads a few times before you need to replace your rotors. however there can be some conditions that make it necessary to replace the rotors sooner. Let’s look at a few.
Rotor Wear:
The easiest thing to check is the rotor wear limit.
A Magura rotor that is less than 1.8mm wide is considered worn. SRAM rotors less than 1.5mm are worn. Shimano rotors less than 1.5mm or if any of the aluminum “Ice-Tech” material appears are considered worn.
Running too thin of a rotor will compromise brake bite as well as heat capacity. In extreme cases it can lead to rotor separation which will cause damage and potentially severe injury.
Rotor Shape:
If the previous pads have worn shapes into the rotor your performance will be compromised. Whether the rotor shows knife edge, bulge or convex anything but parallel surfaces will cause contact patch issues.
These issues will create extreme “hot-spots” on the new brake pads which, in some conditions, can super heat the pad – glazing it and compromising the friction coefficient (bite, power, heat capacity are all effected).
We have seen cases where new brake pads become unusable due to this severe heat modifying the pad’s makeup glazing not just the contact surfaces but essentially glazing the entire pad material.
A rule of thumb is rotors should be replaced about every three or four sets of pads. It will pay dividends to check the rotor’s condition before installing new pads!
SRAM 00.5318.003.003 Pad Shape 58
Replacement brake pads for the following SRAM Brakes:
SRAM Trail Organic Brake Pads with Aluminum Backer Plate
SRAM Guide Organic Brake Pads with Aluminum Backer Plate
SRAM G2 Organic Brake Pads with Aluminum Backer Plate
